http://24.63.160.194/dsc01325.jpg

http://24.63.160.194/dsc01326.jpg

birdseye-tiger-blackwalnut-zibrawood

beautjful as usual cs!

Sweet CS. What kind of wood is the surfster?

Wow, King me.

Unbelievable!! :eek: :shocked: :drool:
Ahead of the curve all the time!

:kewl: the best CS, the best. :D

Very cool . :claps:

Sweet CS. What kind of wood is the surfster?

that's the zibra wood..not bad turning, but h*** to finish...large open pore's.


thxs. guy's ..their fun to build, but the gluing up is another story.

Cool plugs, those laminates are sweet.

forgot one.

http://24.63.160.194/dsc01327.jpg

cocobolo needle.http://24.63.160.194/dsc01203.jpg

Cocobolo. That is some rich looking wood. Love to have some furniture made out of that. Cost an arm and a leg I'll bet. P.

:drool: those are pissa!
save one for me :hee: your jointed's almost done...
those open grains are tough to fill. i put a few coats of clear on them, sand w/ 220 in between, always seem to get tiny pin holes. :wall:

What ? No Epi ? great looking plugs .. look game.. let me borrow one :humpty:

Real nice work Steve :btu:

I hope you had a good dust mask and good dust collection when working with those exotics.

Yea, arn't you afraid you're going to poison the fish :eek5: :eek: :usd:

Very, very nice.

-spence

That Cocobola is Really Really Nice :drool: :drool:

the work of a master.very nice.

:shocked: That needle is sweeeet. Most be a heavy one though Coco is a dence wood , Great job !

Wowza! :shocked: I know my next project in the JakeCave! I have to lay down now.. :claps:

just let me warn you if you play with that coco...it's like iron..it doesn't give at all,,so one opps and you'll be eating your knife or the wood or pulling splinter's out of skin...chatter's like crazy when cutting it .....and keep the vac snoz up against the wood as close as you can[like an inch away] so theres no dust on the loose....great lookin wood fa shore,,,but feels like it's under great preasure and ready to blow at anytime.

thxs. again for the comp's..guy's..on the hunt for other wood's,just have to find abit lrg. pc's. without having to buy a whole log.

just let me warn you if you play with that coco...it's like iron..it doesn't give at all,,so one opps and you'll be eating your knife or the wood or pulling splinter's out of skin...chatter's like crazy when cutting it .....and keep the vac snoz up against the wood as close as you can[like an inch away] so theres no dust on the loose....great lookin wood fa shore,,,but feels like it's under great preasure and ready to blow at anytime.

thxs. again for the comp's..guy's..on the hunt for other wood's,just have to find abit lrg. pc's. without having to buy a whole log.

I've worked with coco b4 but never turned it . What's the supposed danger from the dust ? :huh:

Great job CS - probably took longer to glue up than to turn. AWSOME !!! What did you use for glue and how much pressure to clamp em? Also did the glue have any effect on turning the plugs? :uhoh: :conf:

Cs a couple of questions if you don't mind. How was it doing the through wire drilling? Just wondering if the boring gave you any difficulty. The other question deals with sanding all that end grain, did you spend a lot of time with real fine grit?
But as has been stated goregous work. Always fun to do Something completely different.

the glue I've been using is called "weldwood" made by "dap",,it's a plastic resin glue,,,look's like fine lt. brown powered sugar,,all you do is add a few drop's of water till it turn;s into mudd///if you want it thinner, just add more water,,,what's great about the stuff is the fact that it's dark brown when cured and fills in any gaps or holes...sands to a power too, doesn;t turn to goo when it gets hot from sanding,,,,,been using it since 1969. they also make the same thing that's waterproof,,come's in two can's..one's the powder/one is cranberry colored liquid resin.////clamping time is as long as you want or as little as an hour, depending on how warm the room or air is.

through drilling is slow,,bird's eye/coco are very hard,,I only push the bit in maybe 3/8's of an inch then back off to clear the flute's and let cool. if you try to force it, the wood/bit get's too bloody hot..I've burned up one bit already....sanding the end grain is no different[turning is another] than your normal end to end grain...after roughly shaving to the shape you want, I then use 60 grit to finish the shape,,then 80 grit, then 220,then use the green scrubby pad's too polish.....it goes fast and doesnt take any longer to do than a normal plug/// well! maybe a minute longer.

most if not all exotic woods/cedars etc. have what look's like small little ball's with lot's of hook's attached to them...when inhailed they stick to your lung's like glue,,never to be gragged up again,,,but! I do beleive turning a pc. only now and again won't kill you...it's the people that use the stuff day in an day out may have a bigger problem with it.A good fan/vac/mask can't hurt if your going to make alot of pc's.///I keep a good clean filter in my lrg. shop vac and as stated before,,the hose is right on top of the wood and not 6-8" away.

very nice. inspiring work, i can't wait to get my lathe in early dec.

:kewl: Nice job.

Great answers Cape, Now for the big one.....
.
.
.
.
.
.
.
.
.
How do they swim? :tooth: :eek:

How do they swim? :tooth: :eek:
don't matter.

Steve,
Very Nice :drool:

VB

don't matter.

Wall hangers? Nah I would think that Capesam is one of those guys who no matter what wants to know how they would perform. One cast what's it gonna hurt? Then hang it. okay two cast, ummmm three.

i wouldn't want to be the one tying that knot.

Those are sweet, reel nice CS... :drool:

Txs. Reel.

they'd swim just like the real painted one's...[almost] cept these don't have lead..eveythings the same size wise/no different...but I gotta say it does sure chew up the wood putting them together.