LaPala
07-11-2011, 03:08 PM
http://i72.photobucket.com/albums/i186/LaPala/Lures/TUP6140207.jpg
It's been ages since I have posted here. Now that I have stopped writing a hardbait DIY column for our local fishing magazine here (in Malaysia just in case you wanna ask), I have a bit more time to spare.
SO here goes:
Making a Vibebait from laminating Acrylic - weight distribution test trick.
I won't be very detail in describing the process as I will assume a basic knowledge of lure making is at your disposal already B)
1. These are the components of the lure body that is needed to be cut-out, shaped then glued up together:
http://i72.photobucket.com/albums/i186/LaPala/Lures/TUP1010092.jpg
Copper rods are used for aligning the pieces together.
2. To work out the weighting:
http://i72.photobucket.com/albums/i186/LaPala/Lures/TUP5230048.jpg
Styrofoam sheet is cut and shaped to fit the chambers in the middle piece, this is the closest approximation of air(available to me) that will occupy the chamber once it is glued up.
3. Water test and balance:
http://i72.photobucket.com/albums/i186/LaPala/Lures/TUP5230050.jpg
Just tape weight to the front to get the correct attitude for a vibebait. I'll assume those who will be attempting this has an understanding of how the weight distribution of a vibebait should be and how to get the desired action by varying the distribution. Anyway, this method is a great way to test them all without having to make lure after lure.
4. Weight used earlier on the head is hammered flat and shaped to fit in the head, acrylic cut out to fit head weight that is formed. Future contruction of same lure will just require the head weight be molded. So keep your notes ;)
http://i72.photobucket.com/albums/i186/LaPala/Lures/TUP5230056.jpg
5. This is the end result:
http://i72.photobucket.com/albums/i186/LaPala/Lures/TUP5250001.jpg
Fins are carved from 1.5mm polycarbonate sheet.
and after some splashes of color.
http://i72.photobucket.com/albums/i186/LaPala/Lures/TUP6140204.jpg
Comments, questions and suggestions for improvement most welcomed.
(PS: Just to be fair, I participate in quite a number of lure making forums, so it's copy paste to all of them.:P :P)
It's been ages since I have posted here. Now that I have stopped writing a hardbait DIY column for our local fishing magazine here (in Malaysia just in case you wanna ask), I have a bit more time to spare.
SO here goes:
Making a Vibebait from laminating Acrylic - weight distribution test trick.
I won't be very detail in describing the process as I will assume a basic knowledge of lure making is at your disposal already B)
1. These are the components of the lure body that is needed to be cut-out, shaped then glued up together:
http://i72.photobucket.com/albums/i186/LaPala/Lures/TUP1010092.jpg
Copper rods are used for aligning the pieces together.
2. To work out the weighting:
http://i72.photobucket.com/albums/i186/LaPala/Lures/TUP5230048.jpg
Styrofoam sheet is cut and shaped to fit the chambers in the middle piece, this is the closest approximation of air(available to me) that will occupy the chamber once it is glued up.
3. Water test and balance:
http://i72.photobucket.com/albums/i186/LaPala/Lures/TUP5230050.jpg
Just tape weight to the front to get the correct attitude for a vibebait. I'll assume those who will be attempting this has an understanding of how the weight distribution of a vibebait should be and how to get the desired action by varying the distribution. Anyway, this method is a great way to test them all without having to make lure after lure.
4. Weight used earlier on the head is hammered flat and shaped to fit in the head, acrylic cut out to fit head weight that is formed. Future contruction of same lure will just require the head weight be molded. So keep your notes ;)
http://i72.photobucket.com/albums/i186/LaPala/Lures/TUP5230056.jpg
5. This is the end result:
http://i72.photobucket.com/albums/i186/LaPala/Lures/TUP5250001.jpg
Fins are carved from 1.5mm polycarbonate sheet.
and after some splashes of color.
http://i72.photobucket.com/albums/i186/LaPala/Lures/TUP6140204.jpg
Comments, questions and suggestions for improvement most welcomed.
(PS: Just to be fair, I participate in quite a number of lure making forums, so it's copy paste to all of them.:P :P)