Hello,

I did not know where to post this but I figured that John would move it if necessary. I need to replace two exterior oak thresholds. I have not been able to find them at the usual places and was looking for a custom millwork shop. Any recommendations? I live in Newton.

Thanks,
Steve

For your front and rear doors?

Van Millwork May be able to get them for you,,, back in the day that was a stock item at most yards,,,, linseed oil them before setting...

For your front and rear doors?
Two rear doors
Posted from my iPhone/Mobile device

Van Millwork May be able to get them for you,,, back in the day that was a stock item at most yards,,,, linseed oil them before setting...

I will check with them. Thx
Posted from my iPhone/Mobile device

I remember making them 10/4 or 8/4 oak cut to rough length, joint and plane to thickness, Rip to width, run the other edge over jointer, take the guard off jointer and set fence to how big you wanted rabbet on exterior, there was a rabbeting shelf on jointer and you kept running the stuff across and it would make the taper. Little hand plane work on edges, Rip drip groove on bottom and you’re done
I haven’t seen a new threshold like that in many years
Posted from my iPhone/Mobile device

Horner Millwork....website shows a lot of different sizes.
Posted from my iPhone/Mobile device

Did you try Sterrit? They should have them in stock or could order if you need more than a 4'

They are not like they used to be.... Seems like I am seeing four pieces laminated together more often now whereas they used to be just one or two pieces. New ones require more support under front lip..... seen a number of them split.

I gave up using commercially made thresholds as they never held up usually red oak, laminated and even with linseed oil were useless.
I would recommend a run to Downes and Reader, buy 8/4 dressed White oak to 1 3/4", I think they may have it in the retail rack, and make your own.

I have no affiliation with D&R just been a customer since day one.

If by "People's Republic" you live in Cambridge go to Anderson Mcquaid on Fawcett St.,they literally have everything.... may even have old school white oak thresholds

Ed

[/QUOTE]New ones require more support under front lip..... seen a number of them split.[/QUOTE]

That is what happened to mine. Moved in last year and they were split. Thanks
Posted from my iPhone/Mobile device

I gave up using commercially made thresholds as they never held up usually red oak, laminated and even with linseed oil were useless.
I would recommend a run to Downes and Reader, buy 8/4 dressed White oak to 1 3/4", I think they may have it in the retail rack, and make your own.

I have no affiliation with D&R just been a customer since day one.

If by "People's Republic" you live in Cambridge go to Anderson Mcquaid on Fawcett St.,they literally have everything.... may even have old school white oak thresholds

Ed

I moved out of Cambridge last year. I need to update my location. Thanks for the suggestion.
Posted from my iPhone/Mobile device

Thanks everyone. I will call these places.
Posted from my iPhone/Mobile device

New ones require more support under front lip..... seen a number of them split.[/QUOTE]

That is what happened to mine. Moved in last year and they were split. Thanks
Posted from my iPhone/Mobile device[/QUOTE]

If it is in good shape, I have glued them back together using a domino, which is a larger oval shaped biscuit. It works and the glue joint is strongest point. Just need to add support.

New ones require more support under front lip..... seen a number of them split.

That is what happened to mine. Moved in last year and they were split. Thanks
Posted from my iPhone/Mobile device[/QUOTE]

If it is in good shape, I have glued them back together using a domino, which is a larger oval shaped biscuit. It works and the glue joint is strongest point. Just need to add support.[/QUOTE]

One is toast. The other might be fine. Thanks for the suggestion.