Striper Talk Striped Bass Fishing, Surfcasting, Boating

Striper Talk Striped Bass Fishing, Surfcasting, Boating (http://www.striped-bass.com/Stripertalk/index.php)
-   DIY - Forum (http://www.striped-bass.com/Stripertalk/forumdisplay.php?f=111)
-   -   HVLP Spray Gun for Compressor (http://www.striped-bass.com/Stripertalk/showthread.php?t=85673)

Ian 04-16-2014 10:04 AM

HVLP Spray Gun for Compressor
 
Tried painting my cabinets with a brush, roller, etc. and nothing is working. Read up on the interwebs and found that this type of gun is by far the preferred method for applying paint in areas prone to dripping.

Anyone have any experience with them?

Raider Ronnie 04-16-2014 04:38 PM

LOTS

Ian 04-16-2014 09:35 PM

Quote:

Originally Posted by Raider Ronnie (Post 1039256)
LOTS

Worth it? Im looking between 150 and 200 and have read some extremely positive reviews
Posted from my iPhone/Mobile device

Slipknot 04-17-2014 06:49 AM

by dripping, if you mean the paint running because of being laid on too heavy, then yes maybe an HVLP may help you.
I don't have experience with an HVLP cup gun used with a compressor, never bought one of those, I did have one powered by a turbine but did not like that, not enough volume for me. I do have one that is on a pressure pot but it does not atomize enough for my use, it may work fine for thinner paints like automotive paint but for cabinets I have to thin it a lot. Air assisted airless is more appropriate for cabinets but at a very high cost.
There has been lots of improvement over the years with the technology of HVLP type spray guns. Buy the best you can afford. I think Binks was one of the first to come out with one. good luck

nightfighter 04-17-2014 07:39 AM

Best product I've used for cabinets is Magnalac by M L Campbell. It is a high build lacquer that worked very well in my HVLP sprayer as well as roll and tip. In general I do not like my HVLP sprayer, but the product you are spraying makes a world of difference in the application and the finished product. While Magnalac is very pricey, the end product is worth it. The labor involved with refinishing is wasted if you cheap out on the paint/finish.

My HVLP gun is from Rockler. We have a love/hate relationship.... Not easy to get it atomizing properly and once set up, lays paint at a slow rate. Not exactly High Volume. And I hate cleaning it.

Ian 04-17-2014 10:11 AM

Thanks for the information guys! I am considering getting this gun with possibly a remote pot setup

http://www.spraygunworld.com/product...%204003-15.htm

I think with all the paint projects we have coming up in the new house I will have a lot of places to use such a tool. The $200 or so investment seems worth it to tackle all of those projects with a uniform coat.

Raider Ronnie 04-17-2014 11:24 AM

I would think that your having an issue with drips using a brush or roller, forget about spraying with a gun.
Hire a painter.
Posted from my iPhone/Mobile device

ed morini 04-20-2014 08:37 AM

hvlp
 
It is very important that you have a compressor that that has sufficient cfm's to work the gun. The 10 psi at the tip is considered ok for atomization of the fluid. Having said that the size tip is also very important. For latex usually 1.2- 1.4 tip is required...check paint specs. and gun specs for these tips.

I sprayed exclusively with hvlp both turbine and conversion guns with excellent results, using all types of finish. http://www.gleempaint.com/hvcongunnew.html has a great gun for beginners, and will work with with a smaller compressor..read the accompanying article and check out the tip sizes.

Ed

Ian 04-22-2014 08:43 AM

Quote:

Originally Posted by ed morini (Post 1039752)
It is very important that you have a compressor that that has sufficient cfm's to work the gun. The 10 psi at the tip is considered ok for atomization of the fluid. Having said that the size tip is also very important. For latex usually 1.2- 1.4 tip is required...check paint specs. and gun specs for these tips.

I sprayed exclusively with hvlp both turbine and conversion guns with excellent results, using all types of finish. http://www.gleempaint.com/hvcongunnew.html has a great gun for beginners, and will work with with a smaller compressor..read the accompanying article and check out the tip sizes.

Ed

Thanks Ed, I had seen that gun and did some additional googling and others said they had issues with it and recommended the Astro. My mind naturally gravitated that direction due to the lower price of the astro as well. I just bit the bullet and bought the Wagner based on some of the rave reviews I read and the ability to find more real reviews on that gun in comparison with the Astro. I think I'll be happy.

ed morini 04-23-2014 07:28 AM

HVLP
 
Let me know how you make out. Give a shout if you need any help

Ed

Ian 06-18-2014 09:43 PM

Spray gun was an accelerated learning curve, but things came out really nicely... Hard to imagine voluntarily using a brush and roller again if the use case allows the gun.
Posted from my iPhone/Mobile device


All times are GMT -5. The time now is 08:13 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright 1998-20012 Striped-Bass.com