Striper Talk Striped Bass Fishing, Surfcasting, Boating

Striper Talk Striped Bass Fishing, Surfcasting, Boating (http://www.striped-bass.com/Stripertalk/index.php)
-   Rod Building (http://www.striped-bass.com/Stripertalk/forumdisplay.php?f=28)
-   -   new 10' rod build (http://www.striped-bass.com/Stripertalk/showthread.php?t=92011)

Guppy 03-16-2017 01:25 PM

new 10' rod build
 
2 Attachment(s)
I set up the gosa 6K at 23" from the butt, did the table top bit to set the choke point and low and behold there is no choke point.... see below

went with the 27X and a KW8 choke, then set KW's down the reduction line,,, the two stripper locations I ended up with have me puzzled, which is very easy to do seeing as though I pretty much don't know what I'm doing...:-)

also the 20 and 16 hit the reduction line but end up not quite inside what I call the KR COF

if I have a question here,,, getting dizzy,,,,, are either of the stripper locals acceptable,,, ?

Attachment 64018

Attachment 64019

I realize this is probably way over kill with the CAD and all but,,,, I figure it's a good start, plus I'm sitting here waiting for my plotter to complete a map update....

beamie 03-16-2017 07:47 PM

Gup,

I have yet to do a surf rod. Done all kinds of boat rods and 50's and small spinners ........so take this with a grain of salt.

but, That doesn't look right to me. The collector looks very close to the reel. Also very surprised that the frame on the Saragossa doesn't have an angle to it more than that?????

Andy has a 1201m spinner and conv I think he said. Have him take some measurements on his rod and guides so you can cheat a little and compare.

And before you wrap gotta tape on and test cast. To nice of a rod to find out later it could have been layed out better the first time.......

Most guys I believe put the reel seat the distance from their have to your armpit, is that 23 for you?

tysdad115 03-16-2017 08:54 PM

I do , my spinner is an old school one with giant guides..But I'll get some measurements.
Posted from my iPhone/Mobile device

pbadad 03-17-2017 05:50 AM

Take a piece if braid and tie it to the top of reel shaft and loop over top of choke guide and tape off tag end to blank. Slide the 30L till each touches top of guide frame. Tape or secure w/o rings. Slide a K20 next till it touches and same for a K12. You'll only need 3 reduction guides. This set worked great for a VS150. If you line slap on blank consider a KW30, KW25,KW20, KW10 or 12 (CHOKE) AND KW8 or #10 for runners .# 10 OR # 12 tip pending runner size. On another note, the KW16 would be a better ring choice instead of the 20 but lacks the height. I've mixed in a SV16 and bent frame the angle of K guides with good results.

Guppy 03-17-2017 06:08 AM

Not done by a long shot, going to check out that KR GPS method next.
23 armpit

Also Lami off the shelf KR layout is posted here page 7

http://www.lamiglas.com/2010_guide_spacing_chart.pdf

Getting ready! :wid:

Guppy 03-17-2017 06:20 AM

Quote:

Originally Posted by pbadad (Post 1118889)
Take a piece if braid and tie it to the top of reel shaft and loop over top of choke guide and tape off tag end to blank. Slide the 30L till each touches top of guide frame. Tape or secure w/o rings. Slide a K20 next till it touches and same for a K12. You'll only need 3 reduction guides. This set worked great for a VS150. If you line slap on blank consider a KW30, KW25,KW20, KW10 or 12 (CHOKE) AND KW8 or #10 for runners .# 10 OR # 12 tip pending runner size. On another note, the KW16 would be a better ring choice instead of the 20 but lacks the height. I've mixed in a SV16 and bent frame the angle of K guides with good results.

Thanks Billy, I will be doing the hands on, I just like messing with the CAD approach first...
Good info right there.... Thanks again

numbskull 03-17-2017 03:49 PM

With KW guides you typically need to go 30-25-20-12 because the drop from the 30 -20 is too much (the guides end up too far apart).

Don't over focus on the "choke point". It is really an obsolete concept. The idea is to get the line tamed at the collector, transition down to the blank quickly and run it out the rod with small guides. A more current build (recommended by a bright rod builder on SOL...ZAFisher) using inexpensive guides might be KW30-KL20-KL12-choke KT8---kT 8's on out. This means you are using single foot guides out much of the rod (except for the collector) which will fish just fine but you need to take care in transport. The KL guides are higher than their KW counterparts. Or you can just go singles entirely and build a nice rod using KLH25-KLH12-KLM-8-KT8 choke and runners. The GPS software at anglersresource.net can help you with this.

Guppy 03-17-2017 05:33 PM

Thanks George
I was trying to accomplish this KR with double foot but have come to the conclusion I need to mix it up with the KW's.. Kl's/kl-h's
The choke point always give the most trouble and I don't want to screw up this (better than I should have) rod you sold me... :-)

I drew another cad with the KR GPS to locate the choke, I'll post it later, if nothing else it may help someone learn how not to build... LOL

Guppy 03-19-2017 09:14 AM

3 Attachment(s)
lots of good info around here
and here is some totally useless stuff LOL
going to buy a bunch of guides and go at it on the wrapper
Attachment 64034
Attachment 64035
Attachment 64036

oops, what's the best way to hold the guides on for test casting TIA

pbadad 03-19-2017 07:38 PM

I use masking tape . 1/4'

Guppy 03-20-2017 06:02 AM

Thanks

pbadad 03-20-2017 07:20 AM

Gup, I would think using the KW30L @ 20" would work where the 25 is postion, 26' . I made a few 9' rods w/VS 150 reels in that similar position with the L GUIDE. This would shorten to a 3 guide reduction set up.just a thought while you're testing .

Guppy 03-20-2017 04:26 PM

Thanks again Billy,,, I'll look at that

Trying to get the boat ready at the same time here,, life is good... :-)

Guppy 04-26-2017 03:27 PM

3 Attachment(s)
I'm back at this, had to get a couple of boat trips out of my system (and Ricky's LOL ) skunked

This is the plan I used
Attachment 64183

This is where I'm at, guides are taped on
Attachment 64184

test cast this afternoon went less than smooth, brought different size sinkers to the local soccer field,,,, sinkers stuck in ground and had to walk after each cast to dig em out! not too bright hey? :-)

comes back with hookless plugs, same problem with a couple of them,,,,, landed right I guess... but still had to walk to pull out!
Attachment 64185

I suck at casting so not the best test, covered half a soccer field plus about 5 or 10 yards.....

I may mess with the layout or just wrap it and move on

thanks for all the above replys

paradoxjim 04-27-2017 09:42 AM

That aerates the soccer field! Maintenance guys should thank you.

Don't discount the single foot guides. I've been using them more frequently on larger rods and I really like them. They will hold any fish you'll encounter, but you can't bang them around too roughly as they will bend if you're careless.

Guppy 04-27-2017 03:37 PM

The first guide in from the stripper is single foot, wish it was a little taller

Guppy 05-13-2017 02:41 AM

Took her for a spin last night, happy as a clam :-)

numbskull 05-13-2017 03:50 PM

Glad that blank found a good home. Get a big one.

Guppy 05-14-2017 06:57 AM

Quote:

Originally Posted by numbskull (Post 1121937)
Glad that blank found a good home. Get a big one.

Thanks again George

Wish it could help me find my way off the beach after dark,,, LOL
Walked soo far couldn't find the small cut through I came on from....
Senior moment! :-)


All times are GMT -5. The time now is 07:15 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright 1998-20012 Striped-Bass.com