Striper Talk Striped Bass Fishing, Surfcasting, Boating

Striper Talk Striped Bass Fishing, Surfcasting, Boating (http://www.striped-bass.com/Stripertalk/index.php)
-   Boat Fishing & Boating (http://www.striped-bass.com/Stripertalk/forumdisplay.php?f=24)
-   -   Lost a Cylinder (http://www.striped-bass.com/Stripertalk/showthread.php?t=92874)

piemma 10-04-2017 04:45 AM

Lost a Cylinder
 
Lost a Cylinder on the Yami yesterday while 10 miles from the dock. Made it back OK. Pulling this AM. We'll see what my mechanic finds.
Hopefully just a bad plug or plug wire.

Guppy 10-04-2017 05:47 AM

Geees, good luck with it Paul

Rockfish9 10-04-2017 07:39 AM

probably a coil...most of the modern stuff have CDM's that combine switch box and coil in one...... this seems to be the year of the ornery outboard... I've had the same motor since 2004... she's been great...only routine maintenance.. which I do faithfully... it's put me through the ringer this season... I've had gaskets dissolve and foul a carb... accelerator pump injectors go bad ( took me forever to figure than one out)... a brand new fuel pump (I put it in this spring)go bad/be defective and a few other miscreant problems... more than once limiting where I could fish...it's running great now....just in time to put it away until salmon season in the spring...

Hope you get it running soon.. you guy's still have some season left to fish...it's just about done here for consistent /reliable fishing..

paradoxjim 10-04-2017 01:03 PM

You were considering selling it last spring, and this is the payback you get for keeping it!? Better get that looked at so we can fish next year.

piemma 10-04-2017 03:38 PM

Quote:

Originally Posted by paradoxjim (Post 1129327)
You were considering selling it last spring, and this is the payback you get for keeping it!? Better get that looked at so we can fish next year.

Yeah, your right Jim. I think Joe is on target with the coil. Mechanic took a quick look and the upside was all 4 cylinders have 150# compression which is factory spec. Downside is 2 of the 4 plugs were wet which means they weren't firing. New wires, plugs and next steps tomorrow.

bassballer 10-04-2017 06:34 PM

Paul dont you have like 5000 hours on that thing?

piemma 10-05-2017 03:55 AM

Quote:

Originally Posted by bassballer (Post 1129352)
Paul dont you have like 5000 hours on that thing?

Not that much Jay. Maybe like 1200.

Guppy 10-05-2017 06:04 AM

Quote:

Originally Posted by piemma (Post 1129372)
Not that much Jay. Maybe like 1200.

I hope that's not a bad thing..
That's what I've put on mine in 4.5 seasons and she's up to 1500....
I'd hate to have to replace it, :-( $$$$

piemma 10-05-2017 06:20 AM

Quote:

Originally Posted by Guppy (Post 1129374)
I hope that's not a bad thing..
That's what I've put on mine in 4.5 seasons and she's up to 1500....
I'd hate to have to replace it, :-( $$$$

Ray, it appears t be electrical as I have factory spec compression so it's probably not inside. I'll know more today (I hope).

Rockfish9 10-05-2017 06:35 AM

Quote:

Originally Posted by piemma (Post 1129341)
Yeah, your right Jim. I think Joe is on target with the coil. Mechanic took a quick look and the upside was all 4 cylinders have 150# compression which is factory spec. Downside is 2 of the 4 plugs were wet which means they weren't firing. New wires, plugs and next steps tomorrow.

What happens with the CDI units is one bad coil will take the other one out because they share a bias from the trigger.. sometimes you can ohm test them but unlike old conventional coils that will show defective windings they seem OK...sometimes a defect in the potting material does not show on standard test and a shorted diode or open diode doesn't read as bad making them a little harder to diagnose.. as long as compression is good every thing is a relative simple ( albeit expensive at times) fix...

piemma 10-07-2017 09:43 AM

Still down. Got lots of different answers from lots of different people.

Clammer 10-07-2017 07:00 PM

I was gonna e-mail about today ....... we,ll talk ,,,crash time

piemma 10-08-2017 02:19 AM

Looks like I have the dreaded VST filter clog.

Guppy 10-08-2017 05:46 AM

Quote:

Originally Posted by piemma (Post 1129561)
Looks like I have the dreaded VST filter clog.

Been there!
Have the injectors tested and cleaned at the same time plus all new fuel filters.... Dr. Gup :-)

piemma 10-08-2017 07:51 AM

Ya, just spoke to a friend who does this stuff for a living and he said the same thing. I've decided that I am pulling either tomorrow or Monday and taking it to my Yami dealer who has worked on this motor as long as I have owned it.

piemma 10-08-2017 10:33 AM

Big thank you goes out to The Buzzman and Ryan F for more help than you can imagine.
I'll have this issue resolved, one way or the other on Tuesday afternoon.

Rockfish9 10-09-2017 07:41 AM

glad you are on the right track...

piemma 10-09-2017 08:58 AM

Thanks Joe. Think we will get it right tomorrow.

Rockfish9 10-09-2017 09:30 AM

Quote:

Originally Posted by piemma (Post 1129645)
Thanks Joe. Think we will get it right tomorrow.

that's great.... Mine is in it's winter home next to the garage...I'm already making plans for next season.

piemma 10-10-2017 03:01 PM

OK, boat is pulled and home in its house.
Steve Gunther came to the marina and the results are fuel pump, 2 injectors and probably the vst.
He's gonna work on it at my house Sunday but I am done for the season.

Clammer 10-10-2017 08:23 PM

NEW ONE /NEW ONE 150hp

piemma 10-11-2017 03:43 AM

Quote:

Originally Posted by Clammer (Post 1129731)
NEW ONE /NEW ONE 150hp

Maybe!!!!

piemma 10-16-2017 06:03 AM

Great job by Steve Gunther yesterday. Motor is fixed. I'm done for the year but she is ready for next Season!!!

PRBuzz 10-16-2017 07:08 AM

1 Attachment(s)
Glad to hear Paul....yes Gunter Mobile Marine Services are great for anyone needing boat maintenance/repair...his team comes to the boat!

piemma 10-16-2017 07:30 AM

Great guy Phil. Extremely knowledgeable, dependable and reasonable pricing considering he came onsite. I will use him as long as I have a boat.


All times are GMT -5. The time now is 04:26 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright 1998-20012 Striped-Bass.com