Striper Talk Striped Bass Fishing, Surfcasting, Boating

Striper Talk Striped Bass Fishing, Surfcasting, Boating (http://www.striped-bass.com/Stripertalk/index.php)
-   Boat Fishing & Boating (http://www.striped-bass.com/Stripertalk/forumdisplay.php?f=24)
-   -   Bronze Intake Strainer ?????? (http://www.striped-bass.com/Stripertalk/showthread.php?t=86224)

Van 06-25-2014 09:12 AM

Bronze Intake Strainer ??????
 
1 Attachment(s)
Since I had the bottom completely redone this season, I did not replace my plastic strainer over the through hull intake.
Now I keep picking up weeds and clogging my bait well pump.

So I have to pull the boat and re-install a new strainer.
I am thinking of the bronze type rather than plastic.
I used to bottom paint the plastic one.

SOOOO...my question is. does the bronze type have to be bottom painted? Will the copper content in the bronze prevent growth?

saltyric 06-25-2014 09:42 AM

I paint over my bronze strainer with interlux ACT......haven't had any problems. I've been doing it for 9 years

Van 06-25-2014 10:43 AM

What if I don't paint it?

Rockfish9 06-25-2014 11:12 AM

Quote:

Originally Posted by Van (Post 1045647)
What if I don't paint it?

some times they crust with barnacles if you don't paint them....if you go to bronze it needs to be bonded lest you risk sinking the boat due to electrolysis....

Nebe 06-25-2014 01:57 PM

Paint it
Posted from my iPhone/Mobile device

beamie 06-25-2014 03:34 PM

Quote:

Originally Posted by Van (Post 1045647)
What if I don't paint it?

It will grow stuff........paint it.

You are not talking the entire thruhull combination pickup and strainer Van correct..... just a strainer over a regular round thru hull?

........just saw you had the pic...................

thefishingfreak 06-25-2014 05:56 PM

If it's just the screw over the top scoop, just smear some paint on it.
Barnacles will clog it up.
Full thru hull, with valve, has to be grounded like mentioned above
Posted from my iPhone/Mobile device

nightfighter 06-25-2014 06:15 PM

Quote:

Originally Posted by Rockfish9 (Post 1045650)
some times they crust with barnacles if you don't paint them....if you go to bronze it needs to be bonded lest you risk sinking the boat due to electrolysis....

Quote:

Originally Posted by thefishingfreak (Post 1045703)
If it's just the screw over the top scoop, just smear some paint on it.
Barnacles will clog it up.
Full thru hull, with valve, has to be grounded like mentioned above
Posted from my iPhone/Mobile device

The electrolysis is the big issue. Check out your zincs when you haul it out. All it takes is a boat with a bad ground on the next dock to wreak havoc on your boat's parts. Sometimes it's the marina that's discharging.... If I were in a marina, I would hang huge sacrificial zinc fish every time I tied up the boat.....

Van 06-26-2014 07:44 AM

Quote:

Originally Posted by thefishingfreak (Post 1045703)
If it's just the screw over the top scoop, just smear some paint on it.
Barnacles will clog it up.
Full thru hull, with valve, has to be grounded like mentioned above
Posted from my iPhone/Mobile device

OK...paint it.

It should be isolated from anything else. The only metal parts hanging in the water are the engine bracket with its zinc, and the plug which is bronze and still as good as day 1. Funny though, my bronze through hull with valve has never been grounded either and is perfect. 20 years and counting.

Thanks all. Now I have to go get the trailer, drive to the ramp, haul it, screw the stupid thing in place and put her right back in and bring the trailer back to where i store it. (maybe a short trip to a gas station would be in order too...I'll wait until the tank is near empty):uhuh::uhuh::uhuh:

Nebe 06-26-2014 08:39 AM

Check your zinc often. Electrolysis speeds up when you have dissimilar metals under the water line.
Posted from my iPhone/Mobile device


All times are GMT -5. The time now is 01:54 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Copyright 1998-20012 Striped-Bass.com