|
|
|
|
|
|
|
|
|
Plug Building - Got Wood? Got Plug? |
|
09-03-2018, 10:42 AM
|
#1
|
Registered User
Join Date: Nov 2006
Location: Bristol CT
Posts: 316
|
Keeping lip slots clean
What is the best way or better way to keep the lip slot clean during finishing. Been using playing cards but looking for other ideas.
|
|
|
|
09-03-2018, 03:24 PM
|
#2
|
Uncle Remus
Join Date: Mar 2003
Location: Lakeville Ma.
Posts: 14,773
|
i always preferred 1/2 an index card folded over to fit snug in slot.. the card will absorb any extra epoxy and and keep it clean. playing cards, shinny, will repel the epoxy and cause it to build up around the slot. Just got to remember to pull it out before it sets up. I've done it. Will ruin slot and plug.
|
"A beach is a place where a man can feel he's the only soul in the world that's real"
|
|
|
09-03-2018, 03:53 PM
|
#3
|
Registered User
Join Date: Nov 2006
Location: Bristol CT
Posts: 316
|
Thanks Paul. Trying to catch a break with these. Bout ready to throw them in the fire. Between shooting boogers of paint to spilling an entire cup of finish, to now peeling 2 off of the melamine bench top. And trying to scrape off the crap on them.
Posted from my iPhone/Mobile device
|
|
|
|
09-03-2018, 03:59 PM
|
#4
|
Uncle Remus
Join Date: Mar 2003
Location: Lakeville Ma.
Posts: 14,773
|
Haha. The fun of building plugs. We’ve all been there with screwing up in every conceivable way. Good luck.
Posted from my iPhone/Mobile device
|
|
|
|
09-03-2018, 06:39 PM
|
#5
|
Super Moderator
Join Date: Aug 2000
Location: Middleboro MA
Posts: 17,123
|
I try to brush it out of the slot as best as possible then I used to just run one of those Japanese saws thru the slot after.
They are fishing lures, no amount of epoxy is going to save them from the beating they will be given. As long as they swim it doesn't matter to me.
|
The United States Constitution does not exist to grant you rights; those rights are inherent within you. Rather it exists to frame a limited government so that those natural rights can be exercised freely.
1984 was a warning, not a guidebook!
It's time more people spoke up with the truth. Every time we let a leftist lie go uncorrected, the commies get stronger.
|
|
|
09-04-2018, 09:38 AM
|
#6
|
Registered User
Join Date: Feb 2009
Location: New Haven
Posts: 1,260
|
I paint, glue in the lip slot, wire and then finish with epoxy. I get some sporadic build up of epoxy around the lip at times, but not much. Also the lip also gives me a place to hold the plug when putting the epoxy on. I'm certainly not an expert in plug building, nor do I sell them so the final appearance isn't overly important to me.
|
It all started last year during a terrible thunderstorm, when I locked myself out of the house. Shelving myself with a large piece of sheet metal, I ran for cover under the tallest tree I could find!
|
|
|
09-04-2018, 11:16 AM
|
#7
|
Registered User
Join Date: Dec 2002
Location: North Branford,Ct.
Posts: 7,588
|
Kevin i too assembly lip plugs for same reason. Then onto dryer. Pikes dont get wired but lip screws secure lip in w/ epoxy.
Posted from my iPhone/Mobile device
|
|
|
|
09-04-2018, 02:16 PM
|
#8
|
Registered User
Join Date: Sep 2003
Location: Libtardia
Posts: 21,591
|
I used to use index cards that were wrapped in wax paper. The wax paper acts as a release
Posted from my iPhone/Mobile device
|
|
|
|
09-04-2018, 06:00 PM
|
#9
|
Registered User
Join Date: Nov 2004
Location: plymouth,ma
Posts: 1,142
|
I dont epoxy first but sealer gets in there too. I have an old dull band saw blade that I've cut up with tin snips and just pull a short section of that that through the slot and wipe it off. If I dont catch it before it dries, or I'm refinishing pugs that have epoxy in the slot, I've held a piece of the blade in vice grips and heated it up with my little torch til its glowing and then pull it through, goes thru it very easily and the teeth pull it out.
|
|
|
|
09-05-2018, 09:16 AM
|
#10
|
Registered User
Join Date: May 2004
Location: CT/RI
Posts: 1,627
|
I clear first and never have too much of an issue with it getting in the lip slot. I don't have a spinner and use two very light coats so they may be why. If some clear did get in the lip slot I just use a small coping saw to remove it and then when I add lips and wire the plugs I epoxy the lips on place which also ensures the lip slot is well sealed.
|
|
|
|
09-09-2018, 06:09 AM
|
#11
|
Very Grumpy bay man
Join Date: Nov 2003
Location: Rhode Island
Posts: 10,666
|
Quote:
Originally Posted by Slipknot
I try to brush it out of the slot as best as possible then I used to just run one of those Japanese saws thru the slot after.
They are fishing lures, no amount of epoxy is going to save them from the beating they will be given. As long as they swim it doesn't matter to me.
|
Slip, I do the same. I have a few of the Japanese saws and love them.
|
No boat, back in the suds.
|
|
|
09-10-2018, 09:35 AM
|
#12
|
Registered User
Join Date: Aug 2005
Location: the Dirty Jerz
Posts: 276
|
This is a good use for old business cards. They are free (no reason to buy index cards).
|
|
|
|
10-04-2018, 06:16 PM
|
#13
|
Registered User
Join Date: Jan 2010
Location: S. Easton
Posts: 1,676
|
I go to Staples and buy card stock and have them cut them into business cards. For the first application of epoxy I fold the card in the lip slot, after approximately 30 minutes, pull the card out and slide 1-3 new cards through the slot to clean out the epoxy that may have gotten inside the slot. My latest spinner has 10 switches making it easier to stop individual plugs so I can futz with them.
|
"Always two there are, no more, no less: a master and an apprentice." >> Yoda
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 05:56 PM.
|
| |