Need a steel plate

[fishaholic18]

For Clammers trailer.
Can any of you guys make one?
It has to be stainless or galv. steel.
It has to be 6"X3"
with 4 holes for C-clamps.
Holes are 1 3/4" apart and 4" apart.
I'll try to draw a pic to post.

Thanx

[BigFish]

Raider Ron is the man! He might be able to help!

[fishaholic18]

Originally Posted by BigFish

Raider Ron is the man! He might be able to help!

Thanx BF, I want to go Tuna'ing with him too.
Ron, you there?

[Raider Ronnie]

Originally Posted by fishaholic18

For Clammers trailer.
Can any of you guys make one?
It has to be stainless or galv. steel.
It has to be 6"X3"
with 4 holes for C-clamps.
Holes are 1 3/4" apart and 4" apart.
I'll try to draw a pic to post.

Thanx

plate needs to be 6in x 3in ???
How thick??? 1/4 3/8 1/2 ???
And what size holes drilled ??? 1/2
What is is going to be used for ???

[fishaholic18]

Originally Posted by Raider Ronnie

plate needs to be 6in x 3in ???
How thick??? 1/4 3/8 1/2 ???
And what size holes drilled ??? 1/2
What is is going to be used for ???

3/8 thick should do it.
1/2" holes
Used on trailer, front bed holder

[fishaholic18]

Hole measurements are on center

[Raven]

template....

[Young Salt]

if ronnie has trouble i can help you out, toughest part for me would be getting the stock (without having to buy 10')

im close too.......w.warwick

[Raven]

A friend a mine has some left over stainless steel tool box
plate he really doesnt want....which came to mind and
the piece is 3" x 24" or around those measurements...

[striprman]

I'd let ya use the one in my head, but I kinda need it

[Raider Ronnie]

Took a look what I had for stock!
I have some galvi that would work, though it's 1/4 thick but think it's enough for what you need, and I would need to cut to size and when galvi is cut, the edges will be bare metal exposed and I would have to brush some galvi primer to protect it, but not a big deal!
I just called a friend who I get stock from and he thinks he may have some stainless that may work and will call me tomorrow when he looks through his shop!

[Clammer]

this is what Dave took a photo of ;;;;

[fishaholic18]

Yeah Ron, see the pics of what's on there now?
Sh!tty setup, I want the clamps to be above and below the crossmember so I can crank them up tight. The way it is now sux and u can't get the clamps tight enough, just bends the plate. 1/4" should do it. Let me know. If u need a template, I'll draw one and post a pic of it.

[Raider Ronnie]

Originally Posted by fishaholic18

Yeah Ron, see the pics of what's on there now?
Sh!tty setup, I want the clamps to be above and below the crossmember so I can crank them up tight. The way it is now sux and u can't get the clamps tight enough, just bends the plate. 1/4" should do it. Let me know. If u need a template, I'll draw one and post a pic of it.

So you want to u bolt around the crossmember !
What does the plate hold to the trailer anyway??? what kind of bed ???
I'm on it today!!!
My fee,
I want to experience fishing with the Clammer!!!

[Clammer]

R/R

no problem -its your f #%^&*( life

[fishaholic18]

Originally Posted by Raider Ronnie

So you want to u bolt around the crossmember !
What does the plate hold to the trailer anyway??? what kind of bed ???
I'm on it today!!!
My fee,
I want to experience fishing with the Clammer!!!

It's a V-bar thet holds the bow up off the trailer.
The way it is now, the bar keeps sliding down.
Do the measurements make sense Ron?

[thefishingfreak]

one of you guys call ronnie..
508 326 9287
he asked me to post,,,, he sais your plate is done....

[reelecstasy]

RR is da man

[fishaholic18]

Originally Posted by thefishingfreak

one of you guys call ronnie..
508 326 9287
he asked me to post,,,, he sais your plate is done....

Done, thanx again Ron.