| |
 |
|
|
|
 |
|
 |
| |
| Boat Fishing & Boating A new forum at Striped-Bass.com for those fishing from boats and for boating in general |
 |
08-21-2019, 11:36 AM
|
#1
|
|
User
Join Date: Jun 2012
Location: Cape Cod
Posts: 5,454
|
Wash down pump...
Time to retire my 5 gal. bucket wash down routine...
The pump onboard now handles live well ok but need another (stronger) for wash downs,,, tog season almost upon us...:-)
Any recommendations,,, oh, and what’s this pressure switch I see included with some ?
TIA
|
|
|
|
|
|
08-21-2019, 12:04 PM
|
#2
|
|
Registered User
Join Date: Jan 2007
Location: Reading Mass/Newburyport/merrimack river
Posts: 3,748
|
I've had good luck with my sure flow pro blaster, It's been installed under my console for 5 season now, I went through 1 jabsco pump every 2 seasons before getting this one, the supply tee's off my bait pump (also a sure flow)I also have it piped through an accumulator, it helps alot to maintain good pressure..I filled mine with non toxic antifreeze at seasons end to help keep it from corroding (and freezing )
Posted from my iPhone/Mobile device
|
|
|
|
|
|
|
08-21-2019, 12:06 PM
|
#3
|
|
Registered User
Join Date: Jan 2007
Location: Reading Mass/Newburyport/merrimack river
Posts: 3,748
|
Quote:
Originally Posted by Rockfish9
I've had good luck with my sure flow pro blaster, It's been installed under my console for 5 season now, I went through 1 jabsco pump every 2 seasons before getting this one, the supply tee's off my bait pump (also a sure flow)I also have it piped through an accumulator, it helps alot to maintain good pressure..I filled mine with non toxic antifreeze at seasons end to help keep it from corroding (and freezing )
Posted from my iPhone/Mobile device
|
If you do add an accumulator, they always stink like a swamp every time you use them for the first few minutes.
Posted from my iPhone/Mobile device |
A good run is better than a bad stand!
|
|
|
|
|
08-21-2019, 12:08 PM
|
#4
|
|
Registered User
Join Date: Jan 2007
Location: Reading Mass/Newburyport/merrimack river
Posts: 3,748
|
Also the pro blaster has a built in 45 PSI switch, that shuts the pump off above 45 psi so you don't blow up hoses.
Posted from my iPhone/Mobile device
|
|
|
|
|
|
|
08-21-2019, 01:02 PM
|
#5
|
|
Registered User
Join Date: Nov 2003
Location: On my boat
Posts: 9,698
|
Those pumps are toys !
Install a new 1 1/2 seacock with a pick up scoop under the boat.
Then install a Rule 17A as close or even better directly off the seacock.
1 1/2 hose off pump to the deck
(White vacuum wire reinforced hose sold at West Marine)
If you want high pressure find a reduction barbed fitting to bring the 1 1/2 hose down to 1/2 diameter with give you 3800 gallons per hr and high pressure.
Posted from my iPhone/Mobile device
Last edited by Raider Ronnie; 08-21-2019 at 09:54 PM..
|
|
|
|
|
|
|
08-21-2019, 01:59 PM
|
#6
|
|
Registered User
Join Date: Jan 2007
Location: Reading Mass/Newburyport/merrimack river
Posts: 3,748
|
Quote:
Originally Posted by Raider Ronnie
Those pumps are toys !
Install a new 1 2/2 seacock with a pick up scoop under the boat.
Then install a Rule 17A as close or even better directly off the seacock.
1 1/2 hose off pump to the deck
(White vacuum wire reinforced hose sold at West Marine)
If you want high pressure find a reduction barbed fitting to bring the 1 1/2 hose down to 1/2 diameter with give you 3800 gallons per hr and high pressure.
Posted from my iPhone/Mobile device
|
I can see the head line now, man sinks 18' boat with wash down hose.. be real Ron... not every boat needs to flood the deck with an 1 1/2" hose, just storing it in a small boat would be a nightmare..my " "toy" does a very nice/fast job of cleaning the boat after hauling lobster pots, bleeding/gutting a limit of haddock, cleaning muck after a morning of clamming or cleaning up after snagging pogies..just like it is supposed to do..
When I had my Holland, the choice was simualr to what you describe.. it had to be.. |
A good run is better than a bad stand!
|
|
|
|
|
08-21-2019, 02:14 PM
|
#7
|
|
Seldom Seen
Join Date: May 2001
Posts: 10,505
|
Quote:
Originally Posted by Rockfish9
I can see the head line now, man sinks 18' boat with wash down hose.. be real Ron... not every boat needs to flood the deck with an 1 1/2" hose, just storing it in a small boat would be a nightmare..my " "toy" does a very nice/fast job of cleaning the boat after hauling lobster pots, bleeding/gutting a limit of haddock, cleaning muck after a morning of clamming or cleaning up after snagging pogies..just like it is supposed to do..
When I had my Holland, the choice was simualr to what you describe.. it had to be..
|
LMAO Had to be said. Perfect guy to say it too!  |
“Americans have the right and advantage of being armed, unlike the people of other countries, whose leaders are afraid to trust them with arms.” – James Madison.
|
|
|
|
|
08-21-2019, 04:12 PM
|
#8
|
|
User
Join Date: Jun 2012
Location: Cape Cod
Posts: 5,454
|
Thanks Joe.. and Ron if I ever buy a battleship I’ll set er up just like that.... LOL ;-) and thank you...
Have I got this right,,, I turn the pump on at the helm, the pump fires off and when the pressure reaches design, the motor shuts down til the wash down hose is used... yes?
I like that if that’s the case , been on a couple boats that have switch on pump on , switch off pump off ,,, that’s it !,,,
I won’t mention who Wayne and Niko... LOL
|
|
|
|
|
|
|
08-21-2019, 05:43 PM
|
#9
|
|
Idiot
Join Date: Jul 2012
Location: Glastonbury, CT
Posts: 2,287
|
I’ve been contemplating the same addition to my ride, this popped up on another site’s deal thread today
https://www.hodgesmarine.com/Shurflo...48-153-e09.htm
Posted from my iPhone/Mobile device |
|
|
|
|
|
|
08-21-2019, 08:18 PM
|
#10
|
|
Seldom Seen
Join Date: May 2001
Posts: 10,505
|
That's a good deal, even compared to Amazon, before shipping... But if you are adding, as opposed to just replacing the pump, look into the Ultimate .kit, which includes the strainer, hose, nozzle, and most if not all the connections you would need to hook up to the seacock. At least look at the list of fittings to compare to what you will have to buy.
https://www.hodgesmarine.com/Shurflo...58-153-e09.htm |
“Americans have the right and advantage of being armed, unlike the people of other countries, whose leaders are afraid to trust them with arms.” – James Madison.
|
|
|
|
|
08-21-2019, 09:52 PM
|
#11
|
|
Registered User
Join Date: Nov 2003
Location: On my boat
Posts: 9,698
|
Quote:
Originally Posted by Rockfish9
I can see the head line now, man sinks 18' boat with wash down hose.. be real Ron... not every boat needs to flood the deck with an 1 1/2" hose, just storing it in a small boat would be a nightmare..my " "toy" does a very nice/fast job of cleaning the boat after hauling lobster pots, bleeding/gutting a limit of haddock, cleaning muck after a morning of clamming or cleaning up after snagging pogies..just like it is supposed to do..
When I had my Holland, the choice was simualr to what you describe.. it had to be..
|
So what’s the lifespan of These little pea squirted pumps with the pressure switch before they rust up and #^&#^&#^&#^& the bed, 1-2 years ?
Posted from my iPhone/Mobile device |
|
|
|
|
|
|
08-22-2019, 02:12 AM
|
#12
|
|
User
Join Date: Jun 2012
Location: Cape Cod
Posts: 5,454
|
The one I’m lookin at has a 3 yr. warranty, plenty good pump for a 20 footer and a replacement for the 5 gal. bucket... :-)
|
|
|
|
|
|
|
08-22-2019, 04:55 AM
|
#13
|
|
Seldom Seen
Join Date: May 2001
Posts: 10,505
|
Quote:
Originally Posted by Raider Ronnie
So what’s the lifespan of These little pea squirted pumps with the pressure switch before they rust up and #^&#^&#^&#^& the bed, 1-2 years ?
Posted from my iPhone/Mobile device
|
I got my 1993 Grady in 2007. Replaced the original Shurflo in 2013. It gets regular use on my watch. So no complaints, other than access. Need another elbow to do the change out...YMMV |
“Americans have the right and advantage of being armed, unlike the people of other countries, whose leaders are afraid to trust them with arms.” – James Madison.
|
|
|
|
|
08-22-2019, 05:37 AM
|
#14
|
|
Registered User
Join Date: Nov 2003
Location: On my boat
Posts: 9,698
|
Quote:
Originally Posted by Guppy
The one I’m lookin at has a 3 yr. warranty, plenty good pump for a 20 footer and a replacement for the 5 gal. bucket... :-)
|
Go to West marine for it and get the extended warranty.
Best $20 you can spend.
Also, no matter which style you get buy a Rule.
Their warranty policy is the best and very liberal
Posted from my iPhone/Mobile device |
|
|
|
|
|
|
08-22-2019, 12:07 PM
|
#15
|
|
Registered User
Join Date: Jun 2012
Location: Somerset MA
Posts: 9,197
|
Quote:
Originally Posted by Guppy
Thanks Joe.. and Ron if I ever buy a battleship I’ll set er up just like that.... LOL ;-) and thank you...
Have I got this right,,, I turn the pump on at the helm, the pump fires off and when the pressure reaches design, the motor shuts down til the wash down hose is used... yes?
I like that if that’s the case , been on a couple boats that have switch on pump on , switch off pump off ,,, that’s it !,,,
I won’t mention who Wayne and Niko... LOL
|
My pressure switch works if you dont have any leaks that is  |
|
|
|
|
|
|
08-22-2019, 01:34 PM
|
#16
|
|
Registered User
Join Date: Jan 2007
Location: Reading Mass/Newburyport/merrimack river
Posts: 3,748
|
Quote:
Originally Posted by Guppy
Thanks Joe.. and Ron if I ever buy a battleship I’ll set er up just like that.... LOL ;-) and thank you...
Have I got this right,,, I turn the pump on at the helm, the pump fires off and when the pressure reaches design, the motor shuts down til the wash down hose is used... yes?
I like that if that’s the case , been on a couple boats that have switch on pump on , switch off pump off ,,, that’s it !,,,
I won’t mention who Wayne and Niko... LOL
|
yes, once the pressure is reached is shuts down..mine is on season # 5..the plastic bladder is a little pricey at west marine, around 60 bucks, you might find it cheaper somewhere else, but IMHO, it makes a better installation. |
A good run is better than a bad stand!
|
|
|
|
|
08-22-2019, 01:53 PM
|
#17
|
|
Registered User
Join Date: Jan 2007
Location: Reading Mass/Newburyport/merrimack river
Posts: 3,748
|
Quote:
Originally Posted by wdmso
My pressure switch works if you dont have any leaks that is |
so you hear it go urmmmp.. then stop.... then urrrrmp then stop.. been there.I'm on my 3rd wash down hose, those things aint made to last.
and any hose connection below the water line should get 2 Stainless clamps |
A good run is better than a bad stand!
|
|
|
|
|
08-22-2019, 04:18 PM
|
#18
|
|
User
Join Date: Jun 2012
Location: Cape Cod
Posts: 5,454
|
Quote:
Originally Posted by wdmso
My pressure switch works if you dont have any leaks that is |
I wonder who did the installation  |
|
|
|
|
|
|
08-22-2019, 04:21 PM
|
#19
|
|
User
Join Date: Jun 2012
Location: Cape Cod
Posts: 5,454
|
Went lookin in Bahston harbor today for fish to pay for it,,,
That didn’t work out at all... LOL
|
|
|
|
|
|
|
08-23-2019, 07:41 AM
|
#20
|
|
Registered User
Join Date: Jan 2007
Location: Reading Mass/Newburyport/merrimack river
Posts: 3,748
|
Quote:
Originally Posted by Raider Ronnie
So what’s the lifespan of These little pea squirted pumps with the pressure switch before they rust up and #^&#^&#^&#^& the bed, 1-2 years ?
Posted from my iPhone/Mobile device
|
5 years and counting...installed under the console.. still looks like new....I've even run it for 6 hours straight last season when my bait pump died... |
A good run is better than a bad stand!
|
|
|
|
|
09-05-2019, 07:47 PM
|
#21
|
|
User
Join Date: Jun 2012
Location: Cape Cod
Posts: 5,454
|
Put in the ShurFlow 4.0 gpm pump today...
It works great, then it doesn’t work great... dah
It acts like it’s s#^&#^&#^&#^&#^& air, it is s#^&#^&#^&#^&#^& , one minute a ton of pressure the next air mixed in ,,, WTF
No leak on the pressure side.....
It’s getting the water from the live well pump Y fitting ... the lower outlet?
239AB6BB-1515-4DD9-BA4C-70D128F26063.jpeg
That’s s u c k i n g air
|
|
|
|
|
|
|
09-06-2019, 12:11 AM
|
#22
|
|
Idiot
Join Date: Jul 2012
Location: Glastonbury, CT
Posts: 2,287
|
Quote:
Originally Posted by Guppy
Put in the ShurFlow 4.0 gpm pump today...
It works great, then it doesn’t work great... dah
It acts like it’s s#^&#^&#^&#^&#^& air, it is s#^&#^&#^&#^&#^& , one minute a ton of pressure the next air mixed in ,,, WTF
No leak on the pressure side.....
It’s getting the water from the live well pump Y fitting ... the lower outlet?
Attachment 66474
That’s s u c k i n g air |
Do you have a value shutting off the route to the livewell pump when you’re using it? I’m not 100%, but it may be that the flow rate of the pump is creating enough pressure at the “y” where you’re sharing the pickup with the livewell pump that it’s pulling from both directions at that junction. Turning off the ability for it to backflow air from the livewell pump may help you at least troubleshoot the new unit.
Posted from my iPhone/Mobile device |
The artist formerly known as Scratch59.
|
|
|
|
|
09-06-2019, 06:41 AM
|
#23
|
|
User
Join Date: Jun 2012
Location: Cape Cod
Posts: 5,454
|
Quote:
Originally Posted by Ian
Do you have a value shutting off the route to the livewell pump when you’re using it? I’m not 100%, but it may be that the flow rate of the pump is creating enough pressure at the “y” where you’re sharing the pickup with the livewell pump that it’s pulling from both directions at that junction. Turning off the ability for it to backflow air from the livewell pump may help you at least troubleshoot the new unit.
Posted from my iPhone/Mobile device
|
Thought that might be it also, shut the valve in the LW tank and problem still...
the seacock with LW pump is in an impossible location, can only reach it with one hand....
this ain’t going to b fun :-( |
|
|
|
|
|
|
09-06-2019, 07:00 AM
|
#24
|
|
Registered User
Join Date: Sep 2003
Location: Libtardia
Posts: 21,591
|
This problem could be what you are experiencing in some form.
https://youtu.be/cweD5wJ6nh8
Posted from my iPhone/Mobile device |
|
|
|
|
|
|
09-06-2019, 08:30 AM
|
#25
|
|
Registered User
Join Date: Jan 2007
Location: Reading Mass/Newburyport/merrimack river
Posts: 3,748
|
the bladder takes a lot of that surging and sputtering away..
|
A good run is better than a bad stand!
|
|
|
|
|
09-06-2019, 01:08 PM
|
#26
|
|
Very Grumpy bay man
Join Date: Nov 2003
Location: Rhode Island
Posts: 10,666
|
Quote:
Originally Posted by Guppy
Thought that might be it also, shut the valve in the LW tank and problem still...
the seacock with LW pump is in an impossible location, can only reach it with one hand....
this ain’t going to b fun :-(
|
Ray, remember I had the same boat. I moved mine in the off season so I could get at it with ease. |
No boat, back in the suds.  
|
|
|
|
|
09-06-2019, 04:32 PM
|
#27
|
|
User
Join Date: Jun 2012
Location: Cape Cod
Posts: 5,454
|
Quote:
Originally Posted by Rockfish9
the bladder takes a lot of that surging and sputtering away..
|
Ummm, I don’t get it Joe, esplane plz :-) |
|
|
|
|
|
|
09-07-2019, 09:29 AM
|
#29
|
|
Registered User
Join Date: Jan 2007
Location: Reading Mass/Newburyport/merrimack river
Posts: 3,748
|
Quote:
Originally Posted by Guppy
Ummm, I don’t get it Joe, esplane plz :-)
|
I know you are having a air / prime problem, but by installing a small bladder (plastic one was about 60bucks) it keeps a steady pressure and stops the surging, I found when I put mine in it primed a lot easier. .
I'll take some pictures of my set up next time I go down to the boat.
Posted from my iPhone/Mobile device |
A good run is better than a bad stand!
|
|
|
|
|
09-08-2019, 06:45 AM
|
#30
|
|
User
Join Date: Jun 2012
Location: Cape Cod
Posts: 5,454
|
Quote:
Originally Posted by Rockfish9
I know you are having a air / prime problem, but by installing a small bladder (plastic one was about 60bucks) it keeps a steady pressure and stops the surging, I found when I put mine in it primed a lot easier. .
I'll take some pictures of my set up next time I go down to the boat.
Posted from my iPhone/Mobile device
|
Now I get it! Thanks |
|
|
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 07:33 PM.
|
| |
Linear Mode
