Alternative to Korkers... - Page 4 - Striper Talk Striped Bass Fishing, Surfcasting, Boating

Rob Rockcrawler · 03-06-2011, 08:21 PM

I dont know if the 3/4" would work or not, that would dig in pretty far. I didnt use washers. If i notice that it isnt cutting it as is, i will add them.

ivanputski · 03-06-2011, 08:38 PM

Rob... I have the 1/2 " wearbars... Keep in mind that felt compresses, and the tip of a 3/4" screw will likely stick you.

Ken_J · 03-07-2011, 03:48 PM

I was talking to pbadad about it and he mentioned that along with the ss washer, you may get away with it, but could have to grind down a few of them -

its a tough call at 50$ a set

thanks guys

ivanputski · 03-07-2011, 09:18 PM

the 1/2" ones are perfect...

Haus · 03-07-2011, 11:31 PM

I use simms rivershed boot with vibram sole. Perfect for me. The weight of the boot isn't that bad. I'm kinda in shape so the weight isn't an issue. As for the wearbars, I remove them after each season and screw them back in just next to the old hole.
Posted from my iPhone/Mobile device

Ken_J · 03-16-2011, 10:30 PM

I went 1/2" and they are installed now with 22 per boot.

I am looking forward to using them later on this year.

Thanks Ivan, pbadad, Thumper, and everyone else

piemma · 07-06-2011, 11:38 AM

Quote:

Originally Posted by Ken_J

I went 1/2" and they are installed now with 22 per boot.

I am looking forward to using them later on this year.

Thanks Ivan, pbadad, Thumper, and everyone else

I am on my second year with the 1/2" Wearbars. Granted I only fish the canal a month in the Spring and 6 weeks in the Fall but they are worth every penny I paid. I LOVE them. I have them on a pair of cabelas felt sole wading boots.

ivanputski · 07-06-2011, 12:03 PM

ACHASE: this year i dipped the threads in marine epoxy prior to installation. a few do loosen every now and then . one thing i have found is that large washers with small hole help keep them upright. i will post a pic of my new set up...

I strongly urge as many people as possible to email korkers a link to this thread in order to give them a glimpse of what we need and want... not what they THINK we need or want.

Send a brief, polite, concise, and convincing email to:

SamH@Korkers.com

Sam Houser
Korkers Sales & Marketing Support Coordinator
800-524-8899

I have been emailing him for the last 2 years... he is convinced that I simply dont know what I want, and that their interchangeable (GARBAGE) soles are the answer to all my troubles.

I have basically been telling him that they need to make a bood with receiver threads built directly INTO the sole, so spikes can be screwed in, and LEFT IN...

If he gets enough emails, he'll get the idea that it's not just one guy looking for this type of boot.

Redsoxticket · 03-16-2011, 11:16 PM

The spikes in the felt higher then those on the pods ?
How would you make them the same height ?
I am guessing a washer on the pods and no washer on the felt.
Posted from my iPhone/Mobile device

Ken_J · 03-16-2011, 11:52 PM

yeah, ill add the washers when I get them

also, you screw the felt ones in a little tighter and it compresses the felt a little bit and goes in a little deeper, further leveling everything out (not crazy tight, just a little tighter)

I cant even see any height difference at all with the naked eye just doing what I did stated above

Quote:

Originally Posted by Redsoxticket

The spikes in the felt higher then those on the pods ?
How would you make them the same height ?
I am guessing a washer on the pods and no washer on the felt.
Posted from my iPhone/Mobile device

O.D. Mike · 03-17-2011, 07:52 AM

Old pair of boots, instead of throwing them away. Throw as many 3/8 stainless hex head screws in them.

One box of 3/8 stainless screws, $12 per 100 = 2-seasons of fishing

JohnR · 03-17-2011, 08:16 AM

ODM - I can say, not even close to the wearbars as I did that for a few weeks prior to getting the wearbars

- Cheap & easy solution and perfectly fine for some areas but choose the wearbars when the need for grippiness increases

Wearbars =

O.D. Mike · 03-17-2011, 08:27 AM

Quote:

Originally Posted by JohnR

ODM - I can say, not even close to the wearbars as I did that for a few weeks prior to getting the wearbars

- Cheap & easy solution and perfectly fine for some areas but choose the wearbars when the need for grippiness increases

Wearbars =

So are you going to share some of those fishing spots with me

fishbones · 03-17-2011, 11:07 AM

Quote:

Originally Posted by O.D. Mike

Old pair of boots, instead of throwing them away. Throw as many 3/8 stainless hex head screws in them.

One box of 3/8 stainless screws, $12 per 100 = 2-seasons of fishing

Mike, just get the Wearbars. I'm too old and weak to pull you out of the drink if you slip and go in.

O.D. Mike · 03-18-2011, 07:48 AM

Quote:

Originally Posted by fishbones

Mike, just get the Wearbars. I'm too old and weak to pull you out of the drink if you slip and go in.

With all of the boats and structures I have fallen off of fishing in the past, I still can't believe that I haven't fallen into the canal....

JLH · 03-17-2011, 10:50 AM

I used these last season and was very impressed with the wear bars. A lot of times I’m walking a considerable distance (mile+) over paved roads, sidewalks and rocks to get into areas I fish and I wasn’t too sure if the studs would hold up. Over the course of the season I had one of the tips break off of the wear bars and lost 2 out of the boots. I had to replace the boots at the end of the season due to some of the stitching coming undone (shredded by barnacles) but the studs held up very well and I was able to put them into the new boots for the upcoming season.

bigwavedave · 03-17-2011, 09:09 PM

I think Cabellas and Wearbars should be giving the site a VIG or something for all the FREEEE advertising they are gettin.

ivanputski · 03-18-2011, 10:43 PM

The only way to fly!!!

"Snap" · 05-29-2011, 09:04 AM

I have been using KOLDKUTTER screws for a couple years. they are screws for racing motorcycles on the ice. each screw has 6 points do to it's design.
a bag of ( 250 ) 3/8" screws run about $20..
No they don't last forever. yes I have had 1 or 2 pullout. when they dull it takes 10 minutes to change them all out and the cost is minimal..

chefchris401 · 06-30-2011, 01:28 PM

wanted to bump this up and get some follow up info.

how are you guys liking this setup so far? I know thumper is loving them.

how do the boots fit? I wear a 12 in korker cross currents and need to order some cabelas boots.

These seems to be the way to go, the only reason i havent made the jump is I had a few pairs of korker insoles and extra studs laying around, but my korker insoles delaminated

so i put a pair in from last season and lost 8 studs and the part they screw into on one outing

so they need to go asap.

Thanks as always guys.

Rob Rockcrawler · 06-30-2011, 06:35 PM

This has been one of the most informative threads on SB. I started using the wear bars this year and love em. I havent broken off a stud yet and havent fallen on my arse either. They grip like korkers. Next pair of boots i will be using washers as well. Something to give it just a bit more distance between the studs and my feet. A couple of them create pressure points. Ok for the first 3 hours or so, but gets tough after that.

achase · 07-06-2011, 09:23 AM

Guys,
First off, thanks a million times for this thread. I've been using the 1/2" wearbars in my Korkers boots (felt sole) this season and it's really been amazing. Now my question..
I've been losing a couple of studs here and there after long walks and fishing sessions in some nasty, rocky areas. I also need to re-tighten the wearbars before trips. One thought is that the felt has gotten too compressed over time (couple seasons old) and isn't giving enough to bite into.
Anyway, curious to know if anyone else is losing studs and if you've come up with any solutions?
Again, thanks for the help.
Andrew

pbadad · 07-06-2011, 09:25 PM

Quote:

Originally Posted by achase

Guys,
First off, thanks a million times for this thread. I've been using the 1/2" wearbars in my Korkers boots (felt sole) this season and it's really been amazing. Now my question..
I've been losing a couple of studs here and there after long walks and fishing sessions in some nasty, rocky areas. I also need to re-tighten the wearbars before trips. One thought is that the felt has gotten too compressed over time (couple seasons old) and isn't giving enough to bite into.
Anyway, curious to know if anyone else is losing studs and if you've come up with any solutions?
Again, thanks for the help.
Andrew

I use the 3/4" threaded studs in my Cabelas guide boots. The threaded receiver uses a nip taken off the thread to about 1/2" then I thread the full length in the felt sole w/o the receiver. I use 21 in my boot sole. I think 13 in the receivers and the rest in the feltsole. OK for now.

achase · 07-06-2011, 10:51 PM

Thanks for the suggestions.
Think I'll take out all my wearbars and re-thread w/ the epoxy. Might do it with the washers but I'm a bit scared about reducing the number of threads threads biting into the felt.
Not having to wear the korker's sandals over my boots has been life-changing. Really great!
By the way, I tried the Kold Kutter screws suggested in one of the posts
in this thread in another pair of boots and they're pretty grippy but the head-height is just not enough to bite through weed-covered rocks even after giving them a good scraping-off with the bottom of my boot.
I'm sure the'll be good for something, though.
Ivan, I will write to Korkers.

Liv2Fish · 07-07-2011, 08:48 AM

I just ordered the 3000B - 2 -20 packs and a tool to install / remove them. $80 with shipping. I'll have them tomorrow and will update on performance as soon can get them down to the canal for the east tide.

http://www.gripstuds.com/wader_studs/wader_studs.html

Redsoxticket · 07-06-2011, 10:01 AM

I have yet to see a review on the durability on the newer style 2011 korker boots. Anyone out here with experience on these boots.
______________________

The fact that studs fall out and damaging the rubber footing make me hesitant on acquiring the ultralite wearbar boots.
Posted from my iPhone/Mobile device

JohnnySaxatilis · 07-06-2011, 10:26 AM

here's my alternative to korkers which i'm loving so far this season. N. Face trail/wet shoes, on the closeout table at ems for like 35 bucks. and screw in simms "hard bite" 2 piece cleats made for their wader boots. just screwed them into the rubber, boom. havent lost one yet. awesome for the ditch, and the jetty's round here. dont mind if the feet are in the water they dry out quick. pretty much eliminated the use of my k5000's unless i really need em rock hopping down in rhody. i freakin love em

makomania · 02-12-2012, 07:04 PM

Quote:

Originally Posted by Redsoxticket

I have yet to see a review on the durability on the newer style 2011 korker boots. Anyone out here with experience on these boots.
______________________

The fact that studs fall out and damaging the rubber footing make me hesitant on acquiring the ultralite wearbar boots.
Posted from my iPhone/Mobile device

kinda "eh" mine are already falling apart after less than a season. the soles still hold a TON of sand and try to pop out on you.

Anybody put the wearbars into the korker soles?

Pete F. · 07-06-2011, 03:21 PM

If they fit horse calks then us big boys would'nt have issues with them rolling out. Dover Saddlery | Large Selection of Quality Horse Shoe Studs.

Redsoxticket · 07-08-2011, 05:33 PM

The pro grip studs have an extra wide grip which is a positive feature. The problem would be that if a washer were to be used the inner diameter of the washer would be to large for such stud.
Let us know how it holds up as they are used throughout the season.
Posted from my iPhone/Mobile device