| |
 |
|
|
|
 |
|
 |
| |
| Classifieds Buy,Sell, or Swap for members only please. NO COMMERCIAL ADVERTISING - thanks...
And if you sell something like a boat through here - throw us a couple bucks for the site please :D |
 |
03-11-2013, 07:28 AM
|
#1
|
|
Registered User
Join Date: Nov 2003
Location: On my boat
Posts: 9,686
|
Looking for an old counter top
Probably a long shot but I'm looking for a large counter top surface.
Possibly someone's done a kitchen or bath remodel.
Preferably with old fashion Formica surface.
Or if someone knows where to buy a very large sheet of Formica or similar material a an inexpensive cost and I can glue it down on a substrate.
Making a figerglass layup table.
Old countertops make a great perfectly flat smooth surface to apply a coat of wax and lay up glass ( coat of wax wax acts as a release).
Looking for something 4x8 or 5x10 would be better.
|
LETS GO BRANDON
|
|
|
|
03-11-2013, 08:41 AM
|
#2
|
|
Registered User
Join Date: Jan 2010
Location: S. Easton
Posts: 1,676
|
table top
its kinda far away...
|
"Always two there are, no more, no less: a master and an apprentice." >> Yoda
|
|
|
|
|
03-11-2013, 09:24 AM
|
#3
|
|
Super Moderator
Join Date: Aug 2000
Location: Middleboro MA
Posts: 17,119
|
4x8 is a big countertop to try and find.
you may consider a sheet of duraclad/melamine
the depot or lowes have 4x8 sheets of white melamine 3/4" thick right on the rack for not much more than I pay from a wholesaler.
that would do the same thing, it is basically low pressure laminate as opposed to high pressure laminate.
wax it up good though and maybe finish off the edges with something.
I just got an email today from a supplier that has laminate pretty cheap a buck a sq ft plus tax and shipping, but it would cost about twice than the melamine for a 5x12
if you are going to do a lot of it, then make it so it lasts
|
The United States Constitution does not exist to grant you rights; those rights are inherent within you. Rather it exists to frame a limited government so that those natural rights can be exercised freely.
1984 was a warning, not a guidebook!
It's time more people spoke up with the truth. Every time we let a leftist lie go uncorrected, the commies get stronger.
|
|
|
|
|
03-11-2013, 09:45 AM
|
#4
|
|
Registered User
Join Date: Nov 2003
Location: On my boat
Posts: 9,686
|
Bruce.
I think typical counter top 30-36 inches wide ?
Correct ?
I could to 3 long lengths, build a 2x4 subframe, mount on top of a bench or saw horses & repair seam where 2 lengths meet.
Hoping to find someone demoing a kitchen or similar.
Old 1960-80s Formica kitchen counter tops work great for glassing surface.
UOTE=Slipknot;988519]4x8 is a big countertop to try and find.
you may consider a sheet of duraclad/melamine
the depot or lowes have 4x8 sheets of white melamine 3/4" thick right on the rack for not much more than I pay from a wholesaler.
that would do the same thing, it is basically low pressure laminate as opposed to high pressure laminate.
wax it up good though and maybe finish off the edges with something.
I just got an email today from a supplier that has laminate pretty cheap a buck a sq ft plus tax and shipping, but it would cost about twice than the melamine for a 5x12
if you are going to do a lot of it, then make it so it lasts[/QUOTE]
Posted from my iPhone/Mobile device
|
LETS GO BRANDON
|
|
|
|
|
03-11-2013, 10:06 AM
|
#5
|
|
Registered User
Join Date: Jun 2002
Location: Weymouth, MA Fore River
Posts: 1,258
|
Bargain Outlet - Norwood ??
|
|
|
|
|
|
|
03-11-2013, 10:29 AM
|
#6
|
|
Super Moderator
Join Date: Aug 2000
Location: Middleboro MA
Posts: 17,119
|
typical countertops are 25" deep and if it's a breakfast bar top, should be 36" deep
I think the melamine would work, about 40 bucks for a 4x8 sheet
check salvage places
or like beetle said, bargain outlet
|
The United States Constitution does not exist to grant you rights; those rights are inherent within you. Rather it exists to frame a limited government so that those natural rights can be exercised freely.
1984 was a warning, not a guidebook!
It's time more people spoke up with the truth. Every time we let a leftist lie go uncorrected, the commies get stronger.
|
|
|
|
|
03-11-2013, 11:35 AM
|
#7
|
|
Seldom Seen
Join Date: May 2001
Posts: 10,393
|
Ron,
What I have are short pieces from desks and counters, but none match and some have contoured backsplash molded to them, so wouldn't work to splice together. Check out WilsonArt in Reading. I have picked up the sheets from them to repair counters. Spray adhesive to both sides. Used up last of a sheet on my lathe bench. Be sure you check out the finish as many are matte vs gloss that you want. They don't take cash or deal with the public. Trades only. You can figure that out.
|
|
|
|
|
|
03-16-2013, 08:55 PM
|
#8
|
|
Registered User
Join Date: Jul 2008
Location: petersham,ma
Posts: 222
|
ronnie, i am taking a old counter top out of my camp in the next few weeks...if you want to come get it you can have it. i can measure this week and let you know if you want? its not huge tho...
|
|
|
|
|
|
|
03-17-2013, 06:40 AM
|
#9
|
|
Registered User
Join Date: May 2011
Posts: 685
|
I will be doing a kitchen redo in hull in about a week there are 2 good size counters if you want them ?im also taking cabinets down that would be nice for a shop or garage if anyone interested let me know all white formica
Posted from my iPhone/Mobile device
|
|
|
|
|
|
|
03-17-2013, 07:01 AM
|
#10
|
|
Registered User
Join Date: Aug 2010
Location: A village some where
Posts: 3,436
|
Jason & Shark, whats the sizes please?
Ronnie gets first dibs, but depending on the size i maybe interested, thanks for the follow up.
Posted from my iPhone/Mobile device
|
|
|
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 03:23 PM.
|
| |
Linear Mode
