For Clammers trailer.
Can any of you guys make one?
It has to be stainless or galv. steel.
It has to be 6"X3"
with 4 holes for C-clamps.
Holes are 1 3/4" apart and 4" apart.
I'll try to draw a pic to post.

Thanx

Raider Ron is the man! He might be able to help!:kewl:

Raider Ron is the man! He might be able to help!:kewl:
Thanx BF, I want to go Tuna'ing with him too.
Ron, you there?

For Clammers trailer.
Can any of you guys make one?
It has to be stainless or galv. steel.
It has to be 6"X3"
with 4 holes for C-clamps.
Holes are 1 3/4" apart and 4" apart.
I'll try to draw a pic to post.

Thanx


plate needs to be 6in x 3in ???
How thick??? 1/4 3/8 1/2 ???
And what size holes drilled ??? 1/2
What is is going to be used for ???

plate needs to be 6in x 3in ???
How thick??? 1/4 3/8 1/2 ???
And what size holes drilled ??? 1/2
What is is going to be used for ???
3/8 thick should do it.
1/2" holes
Used on trailer, front bed holder

Hole measurements are on center

template....:bounce:

if ronnie has trouble i can help you out, toughest part for me would be getting the stock (without having to buy 10')

im close too.......w.warwick

A friend a mine has some left over stainless steel tool box
plate he really doesnt want....which came to mind and
the piece is 3" x 24" or around those measurements... :kewl:

I'd let ya use the one in my head, but I kinda need it:conf: :conf: :conf: :smash: :wavey:

Took a look what I had for stock!
I have some galvi that would work, though it's 1/4 thick but think it's enough for what you need, and I would need to cut to size and when galvi is cut, the edges will be bare metal exposed and I would have to brush some galvi primer to protect it, but not a big deal!
I just called a friend who I get stock from and he thinks he may have some stainless that may work and will call me tomorrow when he looks through his shop!

this is what Dave took a photo of ;;;;

Yeah Ron, see the pics of what's on there now?
Sh!tty setup, I want the clamps to be above and below the crossmember so I can crank them up tight. The way it is now sux and u can't get the clamps tight enough, just bends the plate. 1/4" should do it. Let me know. If u need a template, I'll draw one and post a pic of it.

Yeah Ron, see the pics of what's on there now?
Sh!tty setup, I want the clamps to be above and below the crossmember so I can crank them up tight. The way it is now sux and u can't get the clamps tight enough, just bends the plate. 1/4" should do it. Let me know. If u need a template, I'll draw one and post a pic of it.

So you want to u bolt around the crossmember !
What does the plate hold to the trailer anyway??? what kind of bed ???
I'm on it today!!!
My fee,
I want to experience fishing with the Clammer!!!:hidin:

R/R

no problem -its your f #%^&*( life :cheers:

So you want to u bolt around the crossmember !
What does the plate hold to the trailer anyway??? what kind of bed ???
I'm on it today!!!
My fee,
I want to experience fishing with the Clammer!!!:hidin:
It's a V-bar thet holds the bow up off the trailer.
The way it is now, the bar keeps sliding down.
Do the measurements make sense Ron?

one of you guys call ronnie..
508 326 9287
he asked me to post,,,, he sais your plate is done....

RR is da man

one of you guys call ronnie..
508 326 9287
he asked me to post,,,, he sais your plate is done....
Done, thanx again Ron.