| |
 |
|
|
|
 |
|
 |
| |
| Boat Fishing & Boating A new forum at Striped-Bass.com for those fishing from boats and for boating in general |
 |
10-24-2005, 10:47 AM
|
#1
|
|
Registered User
Join Date: Feb 2003
Location: Newtown, CT
Posts: 5,659
|
What cylinder do you have? Some are much easier to rebuild than others. First step is to get the old cylinder out and make sure that the ram is perfectly straight. If it isn't perfectly straight the rebuild won't last very long. You'll probably need a special tool to take the cylinder apart, its called a spanner wrench. If it's a telefles system their website has some great graphics demonstarating what you need and how to do it.
|
|
|
|
|
10-24-2005, 09:02 PM
|
#2
|
|
zoom
Join Date: Apr 2002
Location: Quincy
Posts: 4,145
|
Doubtful the rod is bent, no reason for that, it was fine the last time out and has just been sitting since.(freakin weather) I think it just have sprang a leak.
I have an emial into teleflex, they were very helpful when i had a prob with the helm. I also found seal kits available and these come with the spanner wrench, about 90 bucks.
Just wondering how difficult they are to do.
|
~..~..~.. ><((((º>
Things done at the last possible minute are done with the greatest possible information. Procrastination is, therefore, the most efficient means of doing things.
|
|
|
|
|
10-25-2005, 06:54 AM
|
#3
|
|
Registered User
Join Date: Feb 2003
Location: Newtown, CT
Posts: 5,659
|
A lot depends on how old they are and how much corrosion they have. If they aren't corroded and come apart easily, they are pretty easy to rebuild. If they are really stuck together they can be a Boitch. A bent piston may neo be immediately noticable, but it gradually wears away the seals, so that eventually they fail. Good luck with it.
|
|
|
|
|
|
10-25-2005, 08:30 AM
|
#4
|
|
zoom
Join Date: Apr 2002
Location: Quincy
Posts: 4,145
|
I've been in email contact with teleflex, I'll see what they'll do first.
They have a great customr service.
I let youz know.
|
~..~..~.. ><((((º>
Things done at the last possible minute are done with the greatest possible information. Procrastination is, therefore, the most efficient means of doing things.
|
|
|
|
|
10-26-2005, 09:30 AM
|
#5
|
|
zoom
Join Date: Apr 2002
Location: Quincy
Posts: 4,145
|
After a few e-mails, teleflex is going to send me the end caps (which have the seals) and the spanner wrench------------FREE---------------
They warned me about the rod being damaged, once on my bench I will be able to see whats up. This is another one of my winter projects....
|
~..~..~.. ><((((º>
Things done at the last possible minute are done with the greatest possible information. Procrastination is, therefore, the most efficient means of doing things.
|
|
|
|
|
10-26-2005, 09:57 AM
|
#6
|
|
Registered User
Join Date: Feb 2003
Location: Newtown, CT
Posts: 5,659
|
Van,
Sounds like a good deal to me. The wrench alone is worth about $25. Beware when you take the cylinder apart, there a several other internal seals in there that you'll have to be very acreful not to damage.
|
|
|
|
|
|
11-14-2005, 07:02 PM
|
#7
|
|
zoom
Join Date: Apr 2002
Location: Quincy
Posts: 4,145
|
Got the cylinder in the basement, noticed just a bit of atinaing on the shaft, nothing that won't clean off easy.
BUT, I'm wondering if anyone knows if I pull the shaft out with the center seal to inspect it, will I be able to get it back in ?
Got the kit from teleflex as promised (free), came with the two ends with complete seals, and some o-rings for other fittings. But I want to inspect and clean out the center piston, but I'm not sure, any advice is appreciated.
|
~..~..~.. ><((((º>
Things done at the last possible minute are done with the greatest possible information. Procrastination is, therefore, the most efficient means of doing things.
|
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 11:39 PM.
|
| |
Hybrid Mode