| |
 |
|
|
|
 |
|
 |
| |
| Plug Building - Got Wood? Got Plug? |
 |
11-11-2005, 05:45 PM
|
#1
|
|
Oblivious // Grunt, Grunt Master
Join Date: Nov 2005
Location: over the hill
Posts: 6,682
|
Thru drilling on a drill press
If you don't own a chuck for your lathe, or are trying to thru drill a non-turned plug, try this.
First cut the head off a common nail (something a little thicker than 1/8").
Chuck it in your drill press and sharpen the end with a file while it spins.
Remove it and drill a slightly smaller hole thru a flat board.
Drive the nail thru the board until it's tip projects about 1/4". Cut the back side off flush.
Chuck a cheap small plumb-bod in the center of your drill chuck.
Align the tip of the nail with the tip of the plumb-bob (by lowering the chuck) and then clamp the board to the drill table.
Put a 1/8'' drill in your chuck.
Position one end of your plug on the nail and center the other end under the drill (you can hold it in your hand) then drill in as far as you can.
Flip the plug over and drill in from the other end.
You've now got two aligned pilot holes and can connect them by using a long bit in a hand drill covering half the remaining distance from each end.
I've had good success, although if drilling maple your long bit needs to be kept sharp or else it can wander.
|
|
|
|
|
|
11-11-2005, 07:37 PM
|
#2
|
|
Registered User
Join Date: Feb 2003
Location: Here and There Seasonally
Posts: 5,985
|
Nice! Say...who is this plug builder? Numbskull, you ain't. I'm very grateful for your input.You wouldn't have any plugs to show, would you?
|
He that would make his own liberty secure, must guard even his enemy from oppression; for if he violates this duty, he establishes a precedent that will reach to himself.
Thomas Paine
|
|
|
|
|
11-11-2005, 07:51 PM
|
#3
|
|
Registered User
Join Date: Apr 2002
Posts: 5,945
|
Quote:
|
Originally Posted by Backbeach Jake
Nice! Say...who is this plug builder? Numbskull, you ain't. I'm very grateful for your input.You wouldn't have any plugs to show, would you?
|
Well Said Fred. |
|
|
|
|
|
|
11-11-2005, 09:01 PM
|
#4
|
|
Uncle Remus
Join Date: Mar 2003
Location: Lakeville Ma.
Posts: 14,773
|
Ah Fixtures. I love fixtures.
|
"A beach is a place where a man can feel he's the only soul in the world that's real"
|
|
|
|
|
07-12-2006, 08:45 PM
|
#5
|
|
Super Moderator
Join Date: Aug 2000
Location: Middleboro MA
Posts: 17,125
|
bump
|
The United States Constitution does not exist to grant you rights; those rights are inherent within you. Rather it exists to frame a limited government so that those natural rights can be exercised freely.
1984 was a warning, not a guidebook!
It's time more people spoke up with the truth. Every time we let a leftist lie go uncorrected, the commies get stronger.
|
|
|
|
|
07-12-2006, 08:58 PM
|
#6
|
|
Let's Rock!
Join Date: Apr 2004
Location: Wareham, MA
Posts: 1,208
|
Thanks Again!!!
|
|
|
|
|
|
|
07-13-2006, 07:09 AM
|
#7
|
|
Super Moderator
Join Date: Sep 2003
Location: Georgetown MA
Posts: 18,203
|
This the one I use and it works pretty Pissah!!..
Quote:
|
Originally Posted by #^&#^&#^&#^&#^&#^&#^&#^&#^&#^&#^&
Even easier....ditch the wood and the nail...take a drill bit and turn your table off center. Drill a 1/4" hole in the table and drop a dowel center in the hole when you want to use it. Take it out when done and move the table back. It's aligned front to back PERFECT every time. All ytou need to do to line it up is side to side which can be done easily with a long drill bit.
|
|
"If you're arguing with an idiot, make sure he isn't doing the same thing."
|
|
|
|
07-13-2006, 10:16 AM
|
#8
|
|
Registered User
Join Date: Feb 2005
Location: Burlington
Posts: 2,290
|
Here's a good posting for drilling on a drill press & by hand. Posted by Numbskull when he was a "pro" - now better!
Quote:
|
Originally Posted by numbskull
If you don't own a chuck for your lathe, or are trying to thru drill a non-turned plug, try this.
First cut the head off a common nail (something a little thicker than 1/8").
Chuck it in your drill press and sharpen the end with a file while it spins.
Remove it and drill a slightly smaller hole thru a flat board.
Drive the nail thru the board until it's tip projects about 1/4". Cut the back side off flush.
Chuck a cheap small plumb-bod in the center of your drill chuck.
Align the tip of the nail with the tip of the plumb-bob (by lowering the chuck) and then clamp the board to the drill table.
Put a 1/8'' drill in your chuck.
Position one end of your plug on the nail and center the other end under the drill (you can hold it in your hand) then drill in as far as you can.
Flip the plug over and drill in from the other end.
You've now got two aligned pilot holes and can connect them by using a long bit in a hand drill covering half the remaining distance from each end.
I've had good success, although if drilling maple your long bit needs to be kept sharp or else it can wander.
|
|
low & slow 37
|
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 06:51 AM.
|
| |
Linear Mode
